Nanostation atenna openwrt
Antenas Nanostation M5
descargar Libremesh
veréis la versión que tenéis. Como han venido todas juntas presumiblemente sea la misma (v5.6.2 (XW)).
Entonces desde esa versión HAY QUE HACER DOWNGRADE a la v5.5.X.
La versión se baja de aquí (considerad si teneis modelo XW o XM).
https://www.ubnt.com/download/airmax-m/nanostationm
usr: ubnt
pss: ubntEn “See Past Firmware”
instalar el firmware creado con chef
cambiar ip
ifconfig eth0 10.42.0.40o con dhcp
dhclient -v eth0si ya tiene libremesh la antena
bajar la imagen comporobar el sha5
sisupgrade -n IMAGENAFLASHEARgestión router nanostation
y con el navegador conectar a conectar a
http://10.1.0.1/cgi-bin/luciadmin
pass: 13fMesh network bmx gsf
id nodo XXXXXXXX
id radio nodo XXXXXRd1
LAN publica nodo XX.XX.XX.XX
255.255.255.224¿id mesh gracia GRABCNgsfRb5Rd1MESH?
url de gestión del nodo
http://guifi.net/ca/guifi/device/90165/edit
http://dsg.ac.upc.edu/qmpgsf/index.php
entrar por ssh a la antena e introducir la ip en la config del router según documentado en:
vi /etc/config/limela configuracion
lime-configconfig lime network
# option primary_interface eth0 # The mac address of this device will be used in different places
# option bmx6_over_batman false # Disables Bmx6 meshing on top of batman
option main_ipv4_address '192.0.2.0/24' # Here you have 4 possibilities: set a static IP and the subnet, like '192.0.2.1/16'; parametrize with %Mn and %Nn, and set the subnet, like '192.%N1.%M5.%M6/16'; set a whole network address (so not a specific IP) for getting the IP autocompleted in that network with bits from MAC address, this works also with netmasks other than /24 or /16, like '192.0.128.0/17' (but not valid network addresses, for example '192.0.128.0/16' or '192.0.129.0/17', won't get parametrized); set two different parameters, the first for subnet and the second for IP parametrization, like '192.0.128.0/16/17', this results in /16 subnet but IP parametrized in a /17 range.
option main_ipv6_address '2001:db8::%M5:%M6/64' # Parametrizable in the same way as main_ipv4_address. If used, the IP autocompletion will fill maximum the last 24 bits, so specifying an IP autocompletion range bigger than /104 is not useful.
list protocols adhoc # List of protocols configured by LiMe, some of these require the relative package "lime-proto-...". Note that if you set here some protocols, you overwrite the *whole* list of protocols set in /etc/config/lime-defaults
list protocols lan
list protocols anygw
list protocols batadv:%N1 # Parametrizable with %Nn (which depends from ap_ssid), note that this will range between 16 and 272
list protocols bmx6:13
# list protocols olsr:14
# list protocols olsr6:15
# list protocols olsr2:16
# list resolvers 8.8.8.8 # DNS servers node will use
# list resolvers 2001:4860:4860::8844para quemar imagen por tftp
tftp <ip>
binary
trace on
put <bynary name>
quitpara saber la ipv6
en el terminal
ping6 ff02::1%eth0respondera con la ip
PING ff02::1%eth0(ff02::1%eth0) 56 data bytes
64 bytes from fe80::652e:5e8c:3d4d:2e97%eth0: icmp_seq=1 ttl=64 time=0.029 ms
64 bytes from fe80::46d9:e7ff:fed1:a60c%eth0: icmp_seq=1 ttl=64 time=0.564 ms (DUP!)
64 bytes from fe80::652e:5e8c:3d4d:2e97%eth0: icmp_seq=2 ttl=64 time=0.043 ms
64 bytes from fe80::46d9:e7ff:fed1:a60c%eth0: icmp_seq=2 ttl=64 time=0.485 ms (DUP!)
64 bytes from fe80::652e:5e8c:3d4d:2e97%eth0: icmp_seq=3 ttl=64 time=0.035 ms
64 bytes from fe80::46d9:e7ff:fed1:a60c%eth0: icmp_seq=3 ttl=64 time=0.473 ms (DUP!)
64 bytes from fe80::652e:5e8c:3d4d:2e97%eth0: icmp_seq=4 ttl=64 time=0.057 ms
64 bytes from fe80::46d9:e7ff:fed1:a60c%eth0: icmp_seq=4 ttl=64 time=0.474 ms (DUP!)
--- ff02::1%eth0 ping statistics ---
4 packets transmitted, 4 received, +4 duplicates, 0% packet loss, time 2997ms
rtt min/avg/max/mdev = 0.029/0.270/0.564/0.230 ms